2: 2020-11-08 (日) 17:18:21 maruo[5] [6] | 現: 2020-11-08 (日) 23:15:31 maruo[5] [7] | ||
---|---|---|---|
Line 1: | Line 1: | ||
*Flightrador24とは [#k5945a63] | *Flightrador24とは [#k5945a63] | ||
- | Flightrador24は、ADS-Bの情報など、飛行機が発信するトランスポンダーの情報を元に、機体識別、位置情報などを把握し、一覧化してくれているサービスです。飛行機好きには非常に便利なサービスで、フリーでも使用できるのですが、広告を外したり、機能追加をしようとすると、有償でお金がかかります。 | + | [[Flightrador24:https://www.flightradar24.com]]は、ADS-Bの情報など、飛行機が発信するトランスポンダーの情報を元に、機体識別、位置情報などを把握し、一覧化してくれているサービスです。飛行機好きには非常に便利なサービスで、フリーでも使用できるのですが、広告を外したり、機能追加をしようとすると、有償でお金がかかります。 |
*Feedってなんじゃ? [#bb50485a] | *Feedってなんじゃ? [#bb50485a] | ||
Line 34: | Line 34: | ||
/etc/conf.d/dump1090 | /etc/conf.d/dump1090 | ||
# /etc/conf.d/dump1090 - configuration file for /etc/init.d/dump1090 | # /etc/conf.d/dump1090 - configuration file for /etc/init.d/dump1090 | ||
+ | |||
RECEIVER_OPTIONS="--device-index 0 --gain -10 --ppm 0 --quiet" | RECEIVER_OPTIONS="--device-index 0 --gain -10 --ppm 0 --quiet" | ||
DECODER_OPTIONS="-max-range 360 --fix" | DECODER_OPTIONS="-max-range 360 --fix" | ||
Line 44: | Line 44: | ||
# Copyright 1999-2019 Gentoo Authors | # Copyright 1999-2019 Gentoo Authors | ||
# Distributed under the terms of the GNU General Public License v2 | # Distributed under the terms of the GNU General Public License v2 | ||
+ | |||
depend() { | depend() { | ||
use net | use net | ||
} | } | ||
+ | |||
start() { | start() { | ||
ebegin "Starting dump1090" | ebegin "Starting dump1090" | ||
Line 57: | Line 57: | ||
eend ${?} | eend ${?} | ||
} | } | ||
+ | |||
stop() { | stop() { | ||
ebegin "Stopping dump1090" | ebegin "Stopping dump1090" | ||
Line 71: | Line 71: | ||
まずは[[Flightrador24のページ:https://www.flightradar24.com]]で、アカウント登録を行います。ここで使用したメアドが、以下の設定で使われるので覚えておいてくださいね♪ | まずは[[Flightrador24のページ:https://www.flightradar24.com]]で、アカウント登録を行います。ここで使用したメアドが、以下の設定で使われるので覚えておいてくださいね♪ | ||
さて、コマンド入力しましょう | さて、コマンド入力しましょう | ||
- | # fr24feed --signup | + | # fr24feed --signup |
+ | |||
main][i]FR24 Feeder/Decoder | main][i]FR24 Feeder/Decoder | ||
[main][i]Version: 1.0.18-9/generic | [main][i]Version: 1.0.18-9/generic | ||
Line 78: | Line 79: | ||
[main][i]http://flightradar24.com | [main][i]http://flightradar24.com | ||
[main][i]DNS mode: PING | [main][i]DNS mode: PING | ||
+ | |||
Welcome to the FR24 Decoder/Feeder sign up wizard! | Welcome to the FR24 Decoder/Feeder sign up wizard! | ||
+ | |||
Before you continue please make sure that: | Before you continue please make sure that: | ||
+ | |||
1 - Your ADS-B receiver is connected to this computer or is accessible over network | 1 - Your ADS-B receiver is connected to this computer or is accessible over network | ||
2 - You know your antenna's latitude/longitude up to 4 decimal points and the altitude in feet | 2 - You know your antenna's latitude/longitude up to 4 decimal points and the altitude in feet | ||
3 - You have a working email address that will be used to contact you | 3 - You have a working email address that will be used to contact you | ||
4 - fr24feed service is stopped. If not, please run: sudo service fr24feed stop | 4 - fr24feed service is stopped. If not, please run: sudo service fr24feed stop | ||
+ | |||
To terminate - press Ctrl+C at any point | To terminate - press Ctrl+C at any point | ||
+ | |||
Step 1.1 - Enter your email address (username@domain.tld) | Step 1.1 - Enter your email address (username@domain.tld) | ||
$:<FR24に登録したメールアドレス> | $:<FR24に登録したメールアドレス> | ||
+ | |||
Step 1.2 - If you used to feed FR24 with ADS-B data before enter your sharing key. | Step 1.2 - If you used to feed FR24 with ADS-B data before enter your sharing key. | ||
If you don't remember your sharing key, pelase use the retrival form: | If you don't remember your sharing key, pelase use the retrival form: | ||
http://feed.flightradar24.com/forgotten_key.php | http://feed.flightradar24.com/forgotten_key.php | ||
+ | |||
Otherwise leave this field empty and continue. | Otherwise leave this field empty and continue. | ||
$:<リターンで勝手に設定される> | $:<リターンで勝手に設定される> | ||
+ | |||
Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$:yes | Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$:yes | ||
+ | |||
IMPORTANT: For MLAT calculations the antenna's location should be entered very precise! | IMPORTANT: For MLAT calculations the antenna's location should be entered very precise! | ||
+ | |||
前提ですが、アンテナを設置する場所の緯度、軽度、高度は、国土地理院のホームページの地理院地図で調べられます。緯度、軽度は10進方式で入力。地形の海抜高度がわかりますから、さらにそこからアンテナ設置位置を想定で足し合わせて、さらにフィートに変換して以下に入力します。 | 前提ですが、アンテナを設置する場所の緯度、軽度、高度は、国土地理院のホームページの地理院地図で調べられます。緯度、軽度は10進方式で入力。地形の海抜高度がわかりますから、さらにそこからアンテナ設置位置を想定で足し合わせて、さらにフィートに変換して以下に入力します。 | ||
Step 3.A - Enter antenna's latitude (DD.DDDD) | Step 3.A - Enter antenna's latitude (DD.DDDD) | ||
$:<アンテナ設置位置の緯度を入力> | $:<アンテナ設置位置の緯度を入力> | ||
+ | |||
Step 3.B - Enter antenna's longitude (DDD.DDDD) | Step 3.B - Enter antenna's longitude (DDD.DDDD) | ||
$:<アンテナ設置位置の経度を入力> | $:<アンテナ設置位置の経度を入力> | ||
+ | |||
Step 3.C - Enter antenna's altitude above the sea level (in feet) | Step 3.C - Enter antenna's altitude above the sea level (in feet) | ||
$:アンテナ設置位置高さ | $:アンテナ設置位置高さ | ||
+ | |||
Using latitude: DD.DDDD, longitude: DDD.DDDD, altitude: FFft above sea level | Using latitude: DD.DDDD, longitude: DDD.DDDD, altitude: FFft above sea level | ||
+ | |||
Validating email/location information...OK | Validating email/location information...OK | ||
+ | |||
The closest airport found is ICAO:RJTT IATA:HND near Tokyo. | The closest airport found is ICAO:RJTT IATA:HND near Tokyo. | ||
+ | |||
Latitude: DD.DDDD | Latitude: DD.DDDD | ||
Longitude: DDD.DDDD | Longitude: DDD.DDDD | ||
Country: Japan | Country: Japan | ||
+ | |||
Flightradar24 may, if needed, use your email address to contact you regarding your data feed. | Flightradar24 may, if needed, use your email address to contact you regarding your data feed. | ||
+ | |||
Would you like to continue using these settings? | Would you like to continue using these settings? | ||
+ | |||
Enter your choice (yes/no)$:yes | Enter your choice (yes/no)$:yes | ||
+ | |||
We have detected that you already have a dump1090 instance running. We can therefore automatically configure the FR24 feeder to use existing receiver configuration, or you can manually configure all the parameters. | We have detected that you already have a dump1090 instance running. We can therefore automatically configure the FR24 feeder to use existing receiver configuration, or you can manually configure all the parameters. | ||
+ | |||
Would you like to use autoconfig (*yes*/no)$:yes | Would you like to use autoconfig (*yes*/no)$:yes | ||
+ | |||
Step 6A - Please select desired logfile mode: | Step 6A - Please select desired logfile mode: | ||
0 - Disabled | 0 - Disabled | ||
Line 140: | Line 141: | ||
2 - 72 hour, 24h rotation | 2 - 72 hour, 24h rotation | ||
Select logfile mode (0-2)$:0 | Select logfile mode (0-2)$:0 | ||
+ | |||
Step 6B - Please enter desired logfile path (/var/log): | Step 6B - Please enter desired logfile path (/var/log): | ||
$:/var/log | $:/var/log | ||
+ | |||
Submitting form data...OK | Submitting form data...OK | ||
+ | |||
Congratulations! You are now registered and ready to share ADS-B data with Flightradar24. | Congratulations! You are now registered and ready to share ADS-B data with Flightradar24. | ||
+ Your sharing key (xxxxxxxxxxxxxxx) has been configured and emailed to you for backup purposes. | + Your sharing key (xxxxxxxxxxxxxxx) has been configured and emailed to you for backup purposes. | ||
+ Your radar id is T-RJTTXXX, please include it in all email communication with us. | + Your radar id is T-RJTTXXX, please include it in all email communication with us. | ||
+ Please make sure to start sharing data within the next 3 days as otherwise your ID/KEY will be deleted. | + Please make sure to start sharing data within the next 3 days as otherwise your ID/KEY will be deleted. | ||
+ | |||
Thank you for supporting Flightradar24! We hope that you will enjoy our Premium services that will be available to you when you become an active feeder. | Thank you for supporting Flightradar24! We hope that you will enjoy our Premium services that will be available to you when you become an active feeder. | ||
+ | |||
To start sending data now please execute: | To start sending data now please execute: | ||
sudo service fr24feed start | sudo service fr24feed start | ||
+ | |||
Saving settings to /etc/fr24feed.ini...OK | Saving settings to /etc/fr24feed.ini...OK | ||
Installation and configuration completed! | Installation and configuration completed! | ||
Line 163: | Line 164: | ||
# /etc/init.d/fr24feed start | # /etc/init.d/fr24feed start | ||
- | ちなみに、どうももうひと工夫必要なようで。私は以下の手順を追加しました。 | + | fr24feedが起動している状態で、http://<fr24feedが起動しているIPアドレス>:8754 にアクセスすると、フィーダーの状態がブラウザで表示されます。設定変更とかもできますので、ご確認あれ~♪ |
- | + | ||
- | fr24feedが起動している状態で、http://<fr24feedが起動しているIPアドレス:8754 にアクセスします。サーバの状態がブラウザで表示されます。 | + | |
- | + | ||
- | - 「Setting」をクリック | + | |
- | - 「Host/IP:」を127.0.0.1:30003に設定 | + | |
- | - saveボタンを押して、Restart ボタンを押します。 | + | |
- | + | ||
- | これでうまくいく…と思うなぁ。dump1090のログを見ていると、受信情報はいくつか出てくるんですが、ICAO24ビットアドレスにヒットする情報ってあんまり取れないみたいで。アンテナを統制しないといけないのかな… | + | |
とりあえずうまくADS-Bが捕捉できれば、feedがされてBusinessアカウントが与えられます。お試しあれ~♪ | とりあえずうまくADS-Bが捕捉できれば、feedがされてBusinessアカウントが与えられます。お試しあれ~♪ |
(This host) = https://femt.ddo.jp