Gentoo Linuxな生活​/システム管理関連

サーバの監視に必要なこと anchor.png

サーバ監視で必要なことと言えば、

  • ちゃんと動いているか?

これに尽きると思います。で、ちゃんと動かなくなる要因といえば、

  • ソフトの異常
  • ハードの異常

この2つですね。ソフトの異常はインストールすればすぐにわかります。ハードの異常は、ある日突然やってきたりします。なので、予兆があるかどうかは、日々の監視が必要なのです。

Page Top

何を見ておこうか anchor.png

まず何が壊れると一番まずいか。HDDです。HDDは消耗品ですし、寿命も比較的短いです。ですので、サーバのトラブルと言うと、大体HDDクラッシュが原因です。で、データが論理的に壊れるのは、データ管理に注意さえすれば何とかなります。ハードのクラッシュについては、温度が非常に重要なファクターを持っていると言われます。

Page Top

温度を監視しよう anchor.png

最近のPCは、CPUの発熱も厳しいところから、センサーチップを搭載していたりします。ですので、このセンサーチップを読み取るツールがあればいろんな情報を見ることができます。

Page Top

lm_sensors anchor.png

lm_sensorsと言うツールで、センサーチップの情報を見ることができます。

# emerge lm_sensors

インストール完了~

Page Top

設定 anchor.png

Page Top

カーネル anchor.png

まずカーネルのI2Cドライバーコンフィグレーションを有効化してやります。

<*> I2C support
<M>   I2C device interface
        I2C Algorithms  --->
        I2C Hardware Bus support  --->
        Hardware Sensors Chip support  --->
        Other I2C Chip support  --->

んで、I2C Hardware Bus support や、Hardware Sensors Chip supportも、有効にしておいてやりましょうね。

Page Top

lm_sensors側 anchor.png

# sensors_detect

コマンドを投入します。するてーと、メニュー形式で設定を保存してくれます。あとは

# rc-update add lm_sensors default

でlm_sensorsを起動時に有効にするようにするとi2cデバイスを読み込んでくれます。

Page Top

使い方 anchor.png

# sensors
w83697hf-isa-0290
Adapter: ISA adapter
VCore:     +1.46 V  (min =  +1.71 V, max =  +1.89 V)
+3.3V:     +3.20 V  (min =  +3.14 V, max =  +3.47 V)
+5V:       +4.89 V  (min =  +4.76 V, max =  +5.24 V)
+12V:     +11.55 V  (min = +10.82 V, max = +13.19 V)
-12V:     -11.70 V  (min = -13.18 V, max = -10.80 V)
-5V:       -7.71 V  (min =  -5.25 V, max =  -4.75 V)
V5SB:      +5.54 V  (min =  +4.76 V, max =  +5.24 V)
VBat:      +3.06 V  (min =  +2.40 V, max =  +3.60 V)
fan1:        0 RPM  (min = 51923 RPM, div = 2)
fan2:        0 RPM  (min = 225000 RPM, div = 2)
temp1:       +29°C  (high =    +2°C, hyst =    +0°C)   sensor = thermistor
temp2:     +17.0°C  (high =   +80°C, hyst =   +75°C)   sensor = thermistor
alarms:   Chassis intrusion detection                      ALARM
beep_enable:
         Sound alarm disabled

eeprom-i2c-1-51
Adapter: SiS96x SMBus adapter at 0x10c0
Memory type:            DDR SDRAM DIMM
Memory size (MB):       512

eeprom-i2c-1-50
Adapter: SiS96x SMBus adapter at 0x10c0
Memory type:            DDR SDRAM DIMM
Memory size (MB):       512

eeprom-i2c-0-50
Adapter: ivtv i2c driver #0
Unknown EEPROM type (255).

adm1030-i2c-1-2e
Adapter: SiS96x SMBus adapter at 0x10c0
CPU Fan:  2537 RPM  (min = 1323 RPM, div = 2)
SYS Temp:  +46.8°C  (low  =    +0°C, high =   +60°C)
SYS Crit:    +85°C
CPU Temp:  +48.2°C  (low  =   +40°C, high =   +52°C)
CPU Crit:    +85°C

ほれ、どうですか?ちゃんと出ましたでしょ?つーか、何気にCPUとか、筐体内の温度が高いんだよね。う~ん、対策考えなきゃ、かなー。

Page Top

ASUSマザーボードP8H77-Vでのsensor設定 anchor.png

2013年2月、サーバのマザーを交換したのですが、lm_sensorsでセンサーを検出してくれず、CPU温度しかモニタリングできなくなってしまいました。う~ん…と言うことで、いろいろ調べてみたところ、lm_sensorsを最新化するがよろしと。/etc/portage/package.keywordsに

sys-apps/lm_sensors

を追加してsensors-detect。するとnct6775というセンサーチップが乗っていることが判明。しかし…このセンサーチップ、Linuxカーネル(3.6.11)には入ってないんだよねぇ…しかたがないのでぐぐったところ、Githubにドライバが登録されていることが判明。んで、以下のコマンド投入

# git clone https://github.com/groeck/nct6775.git

カーネルドライバをチェックアウトしてきます。で、自力コンパイル…Makefileと格闘しましたが…

で、/etc/conf.d/lm_sensorsを以下で記述

#
# The format of this file is a shell script that simply defines variables:
# HWMON_MODULES for hardware monitoring driver modules, and optionally
# BUS_MODULES for any required bus driver module (for example for I2C or SPI).

# Load modules at startup
LOADMODULES=yes

# Initialize sensors at startup
INITSENSORS=yes

HWMON_MODULES="coretemp nct6775"

# For compatibility reasons, modules are also listed individually as variables
#    MODULE_0, MODULE_1, MODULE_2, etc.
# Please note that the numbers in MODULE_X must start at 0 and increase in
# steps of 1. Any number that is missing will make the init script skip the
# rest of the modules. Use MODULE_X_ARGS for arguments.
#
# You should use BUS_MODULES and HWMON_MODULES instead if possible.

MODULE_0=coretemp
MODULE_1=nct6775

で、sensorsコマンドを打ってみたら…

acpitz-virtual-0
Adapter: Virtual device
temp1:        +27.8°C  (crit = +106.0°C)
temp2:        +29.8°C  (crit = +106.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Physical id 0:  +38.0°C  (high = +85.0°C, crit = +105.0°C)
Core 0:         +36.0°C  (high = +85.0°C, crit = +105.0°C)
Core 1:         +36.0°C  (high = +85.0°C, crit = +105.0°C)
Core 2:         +28.0°C  (high = +85.0°C, crit = +105.0°C)
Core 3:         +30.0°C  (high = +85.0°C, crit = +105.0°C)

nct6779-isa-0290
Adapter: ISA adapter
in0:                    +0.91 V  (min =  +0.00 V, max =  +1.74 V)
in1:                    +1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in2:                    +3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in3:                    +3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in4:                    +1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:                    +2.04 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:                    +0.37 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in7:                    +3.47 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in8:                    +3.39 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in9:                    +1.06 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in10:                   +0.34 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in11:                   +0.17 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in12:                   +1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in13:                   +1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in14:                   +0.22 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:                     0 RPM  (min =    0 RPM)
fan2:                  1140 RPM  (min =    0 RPM)
fan3:                     0 RPM  (min =    0 RPM)
fan4:                     0 RPM  (min =    0 RPM)
fan5:                     0 RPM  (min =    0 RPM)
SYSTIN:                 +24.0°C  (high =  +0.0°C, hyst =  +0.0°C)  ALARM  sensor = thermistor
CPUTIN:                 +31.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
AUXTIN0:                +95.0°C    sensor = thermistor
AUXTIN1:                +96.0°C    sensor = thermistor
AUXTIN2:               +104.0°C    sensor = thermistor
AUXTIN3:                +17.0°C    sensor = thermal diode
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C
PCH_CHIP_TEMP:           +0.0°C
PCH_CPU_TEMP:            +0.0°C
PCH_MCH_TEMP:            +0.0°C
cpu0_vid:              +0.000 V
intrusion0:            ALARM
intrusion1:            ALARM

見事データがとれました。やれやれ…

Page Top

smartデーモン anchor.png

smartとは、HDDの自己診断機能S.M.A.R.Tのことで、これを導入すると、S.M.A.R.T対応HDDでは自己診断して、やばそう!ってのを教えてくれたりします。

Page Top

インストール anchor.png

# emerge smartmontools

終了~

Page Top

設定 anchor.png

/etc/smartd.confを開きます。ほとんど書いてある例を参考にすればいいのですが、サンプルを参考にちょっと変えて、私はこんな感じで

# DEVICESCAN ←コメントアウトします。
/dev/sda -a -d sat -o on -S on -s (S/../.././04|L/../../6/05) -m mailowner

説明すると、まずDEVICESCANを付けると、それ以降の設定は全て無視されるそうなので、まずはコメントアウト。-aはヘルスチェックステータス、Usageアトリビュートのエラーチェック、Prefailerアトリビュートチェック、Usageアトリビュートチェック、errorログ、selftestログなどを有効にするオプション、-d satは、ATAをSCSIレイヤ使用して使用します。いわゆるSATA向けの設定。-oはオフラインテスト、-S はオートセーブ、-sはショートセルフテストを毎日4時、ロングセルフテストを土曜日の5時からスタート。で-mはステータスの変化があったらmailownerにメールする、てオプション。

これでsmartdを起動すればOK

# rc-update add smartd default

これでS.M.A.R.Tデーモン監視がスタートします。ちなみにコマンドラインでも情報が取れるとです。

# smartctl -a /dev/hda
=== START OF INFORMATION SECTION ===
Device Model:     HDS722516VLAT20
Serial Number:    VNR4GMC4GJR2KM
Firmware Version: V34OA60A
User Capacity:    164,696,555,520 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 3a
Local Time is:    Sun Apr 17 00:10:59 2005 JST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                       was never started.
                                       Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                       without error or no self-test has ever
                                       been run.
Total time to complete Offline
data collection:                 (3585) seconds.
Offline data collection
capabilities:                    (0x1b) SMART execute Offline immediate.
                                       Auto Offline data collection on/off support.
                                       Suspend Offline collection upon new
                                       command.
                                       Offline surface scan supported.
                                       Self-test supported.
                                       No Conveyance Self-test supported.
                                       No Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                       power-saving mode.
                                       Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                       General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  60) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
 1 Raw_Read_Error_Rate     0x000b   100   100   060    Pre-fail  Always       -       0
 2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
 3 Spin_Up_Time            0x0007   134   134   024    Pre-fail  Always       -       229 (Average 216)
 4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       55
 5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
 7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
 8 Seek_Time_Performance   0x0005   100   100   020    Pre-fail  Offline      -       0
 9 Power_On_Hours          0x0012   099   099   000    Old_age   Always       -       8711
10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       55
192 Power-Off_Retract_Count 0x0032   100   100   050    Old_age   Always       -       415
193 Load_Cycle_Count        0x0012   100   100   050    Old_age   Always       -       415
194 Temperature_Celsius     0x0002   125   125   000    Old_age   Always       -       44 (Lifetime Min/Max 25/54)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


Device does not support Selective Self Tests/Logging

こんな感じで情報が出てきます。かなり細かいでしょ?これで相当の情報が得られるはず。セルフテストでNGになってから壊れるとは限りませんけど、最低限の保障はほしいもんね。


トップ   凍結 差分 バックアップ 複製 名前変更 リロード印刷に適した表示   ページ新規作成 全ページ一覧 単語検索 最新ページの一覧   ヘルプ   最新ページのRSS 1.0 最新ページのRSS 2.0 最新ページのRSS Atom Powered by xpWiki
Counter: 6681, today: 1, yesterday: 0
初版日時: 2009-08-19 (水) 00:37:54
最終更新: 2013-02-06 (水) 02:08:12 (JST) (4069d) by maruo
ページ内検索

ログイン

ユーザー名:


パスワード:





パスワード紛失

メインメニュー

サブメニュー
自宅鯖計画

Gentoo Linuxな生活

玄箱HGにGentoo格闘記

航空ショーへ行こう

モータースポーツな世界

奥深き写真の世界への誘い

我思う ゆえに我あり



携帯用QRコード